Skip to content

MaterialsBeginner6 min read

Materials and invert: why one photo needs different settings

The laser darkens wood but lightens black slate, anodized aluminum and painted tile. Learn when to invert, when to mirror, why we lift the midtones, and see our default settings for every material.

The laser does not always make things darker

An engraving file is a map of where to burn: black means burn, white means leave the material alone. What a burn looks like depends on the material. On wood, leather and cork the heat chars the surface, so the mark is darker than the blank. That matches the photo: its dark areas become dark marks.

On other materials the burn uncovers something lighter. Black slate turns pale gray. Anodized aluminum loses its coloured coating and shows silver metal. A painted tile loses its paint and shows white glaze. Clear acrylic and glass frost white. Here the mark is lighter than the surface, so a photo engraved as it is comes out as a negative.

Stainless steel and white tile mark dark, like wood: a fiber laser marks steel directly (diode and CO2 lasers need a marking spray), and on tile the toner or spray that bonds stays dark.

What invert does, and when

Invert flips every tone of the file: black becomes white and light gray becomes dark gray. On a light-marking material that turns the negative back into a positive. The parts of the photo that should look bright now burn, and they show up bright.

You rarely need to think about it. Each material preset in the app knows which way its material marks and inverts for you: Black Slate, Clear Acrylic, Glass, Anodized Aluminum and Painted Tile are inverted, the others are not. The invert happens after the tone curve and your fine-tune and just before dithering, so a brighter slider always means a brighter result on the material.

Two habits keep it right. Do not invert twice: if your laser software also has an invert option, leave it off when the file comes from a light-marking preset. And for a light-marking blank that has no preset of its own, such as a dark coated tumbler, start from a preset that marks light so the file is inverted.

See one photo on four materials

The same photo, previewed four ways. Turn invert off to see why slate and anodized aluminum need it.

Preview, not a burn
Loading the preview
WoodNot inverted
Loading the preview
Black SlateInverted
Loading the preview
Anodized AluminumInverted
Loading the preview
Clear AcrylicInverted · Mirrored

A simple simulation in your browser: the photo goes through the preset's tone curve, invert and mirror, then is tinted between each material's surface and mark colours. It shows which way the marks go, not the exact result, and it skips the dither. Real burns depend on your laser, your settings and the blank.

Mirroring for the back of clear acrylic and glass

Clear acrylic and glass are usually engraved from the back. The frosted marks sit behind the material and you look at them through it, which protects them and adds depth. Seen from the front, an engraving made on the back is reversed left to right, so the file has to be mirrored first.

That is why the Clear Acrylic and Glass presets turn the Mirror switch on by default. Turn it off when you engrave the side you will look at. Text is the quick check: in a file for a back-engraved piece, lettering reads backwards. Mirroring only flips the picture; it does not change any tone, so these two presets are mirrored and inverted.

Tone curves: why we lift the midtones

Materials do not answer the laser in a straight line. Wood darkens a lot: a mid gray in the photo burns well darker than mid gray, and faces go muddy. So the Wood preset lifts the midtones with a gamma of 1.08 and adds a touch of contrast. Leather gets a similar lift (1.1).

A gamma above 1 brightens the middle grays and leaves pure black and pure white where they are. Contrast pushes tones away from the middle. Levels clip the darkest and brightest few values to full black and white. Cork's grain hides fine detail, so its preset also adds local contrast, which boosts detail region by region, and the strongest contrast. Black Slate and Painted Tile are left as they are.

These recipes run inside Smart Auto, after an exposure-aware auto tone that fixes dark or washed-out photos. The Looks and fine-tune sliders then work on top. For how the grays then become dots, see Dithering explained.

Our defaults for every material

Each name links to that material's own guide with settings by laser type, tips and a live try-out.

Default settings per material preset in the app
MaterialThe laser marksInvertMirrorTone recipeDitherDPI
WoodDarkerOffOffMidtones lifted (gamma 1.08), contrast +0.04UltraFrom your laser (254 on diode and CO₂)
Black SlateLighterOnOffAs isUltraFrom your laser (254 on diode and CO₂)
Clear AcrylicLighterOnOnContrast +0.04UltraFrom your laser (254 on diode and CO₂)
LeatherDarkerOffOffMidtones lifted (gamma 1.1), contrast +0.04UltraFrom your laser (254 on diode and CO₂)
CorkDarkerOffOffLocal contrast 1.3, midtones lifted (gamma 1.1), contrast +0.1, levels 6 to 250StuckiFrom your laser (254 on diode and CO₂)
GlassLighterOnOnContrast +0.06, levels 4 to 252UltraLower: 200 to 250
Anodized AluminumLighterOnOffContrast +0.02UltraFrom your laser (254 on diode and CO₂)
Stainless SteelDarkerOffOffContrast +0.04UltraHigher on fiber: 400 to 600
White TileDarkerOffOffMidtones lifted (gamma 1.02), contrast +0.02UltraFrom your laser (254 on diode and CO₂)
Painted TileLighterOnOffAs isUltraFrom your laser (254 on diode and CO₂)

DPI belongs to your laser, not the material: the app starts at 254 DPI for diode and CO₂ lasers. Glass and stainless steel carry their own advice in the preset tip. DPI explained covers the rest.

Burn a test card first

Presets are a starting point, tuned from general engraving practice. Two blanks that look alike can still burn differently: a new batch of slate or another sheet of plywood can shift the right settings. A test card on an offcut costs a few minutes and saves the real piece.

The test card tool in the app makes three cards: a DPI card, a power and speed grid, and a dither strip of your own photo. Pick the material first: for light-marking materials the card is inverted, the same way your photo will be.

Try it in the app

Set your material, size and laser, and ImagePrep360 makes a file at the exact pixel count, with the DPI written in.