DPI is the one number that ties a photo to the laser. Get it right and the burn is even and sharp; get it wrong and the same photo comes out muddy or striped. Here is what the number means on a laser, how it follows from the beam, and how many pixels your file needs.
What DPI means on a laser
DPI means dots per inch, but the dots are different things depending on where the image ends up.
- On a screen the grid of pixels is fixed. The DPI saved in a file changes nothing there; only the pixel count matters.
- On paper a printer lays down many tiny ink dots for every pixel, so 300 DPI is a rule of thumb for how sharp a print looks.
- On a laser the head draws the picture in lines. It travels across the material, fires at evenly spaced spots, steps down and draws the next line. DPI sets both spacings: spots per inch along a line and lines per inch down the piece.
So on a laser one pixel of a dithered file becomes one spot that the beam either burns or skips. That is why the file’s pixel count and the laser’s DPI have to match.
DPI, line interval and scan gap
The step from one line to the next goes by several names: line interval in LightBurn, scan gap or line spacing elsewhere. It is one distance, and it follows from the DPI:
scan gap (mm) = 25.4 ÷ DPI
An inch is 25.4 mm, so at 254 DPI the head steps 0.1 mm per line, at 318 DPI 0.08 mm and at 508 DPI 0.05 mm. The other way round, DPI = 25.4 ÷ scan gap in mm.
Why too high burns and too low stripes
The beam has a real width, its spot size. The DPI decides how far apart the lines are compared with that width.
- Too low. The gap is wider than the spot. Unburned strips stay between the lines, so the engraving looks striped and paler than the file.
- Matched. The gap is about the spot size. The lines meet and tones come out as the file shows them.
- Too high. The gap is smaller than the spot. Every place is hit two or three times, heat builds up, dark tones merge into a muddy patch and the job takes longer.
Past the point where lines overlap, more DPI is not more detail: the beam cannot draw a dot smaller than itself.
From spot size to DPI
Set the scan gap to your spot size and the lines just touch. So the best starting DPI comes straight from the spot:
DPI = 25.4 ÷ spot size (mm) · DPI = 1 ÷ spot size (in)
Spot size to DPI
Or start from a laser preset
| Spot | DPI | Scan gap |
|---|---|---|
| 0.05 mm | 508 | 0.050 mm |
| 0.06 mm | 423 | 0.060 mm |
| 0.08 mm | 318 | 0.080 mm |
| 0.10 mm | 254 | 0.100 mm |
| 0.12 mm | 212 | 0.120 mm |
| 0.15 mm | 169 | 0.150 mm |
| 0.20 mm | 127 | 0.200 mm |
To measure your spot, burn a short single line at low power on anodized aluminum or card and measure its width with a loupe or calipers. Use the width across the lines, in the direction the head steps. Many diode modules have a rectangular spot that is wider one way than the other.
How many pixels your file needs
Each pixel becomes one spot, so the pixels needed on each side are the size in inches times the DPI:
pixels = size (in) × DPI · pixels = size (mm) ÷ 25.4 × DPI
A 4 inch coaster at 254 DPI needs 1016 × 1016 pixels, about one megapixel. A 100 mm tile at 254 DPI needs 1000 pixels a side.
Pixels for a print size
Your photo (optional)
Most phone photos have 3000 or more pixels on the short side, far more than a coaster needs. A small picture saved from the web often has 600 to 800, which gives only 150 to 200 DPI at 4 inches: engrave it smaller, lower the DPI, or upscale it first.
Starting points by laser and material
In ImagePrep360 the DPI comes from the laser you pick. These are the presets:
| Laser | DPI | Scan gap | Note |
|---|---|---|---|
| Diode | 254 | 0.100 mm | Most 5 to 20 W modules have a spot of about 0.08 to 0.1 mm. |
| CO₂ | 254 | 0.100 mm | Standard 2 in lens. Try 318 for extra detail. |
| CO₂ fine | 318 | 0.080 mm | 1.5 in lens or a well-tuned machine. |
| Fiber | 508 | 0.050 mm | Tiny spot, best for metal. |
| Galvo / UV | 423 | 0.060 mm | High-detail galvo marking. |
Most materials work at your laser’s DPI. Three are worth adjusting:
- Glass: frosts rather than burns, and fine dots chip. Use a lower DPI, 200 to 250.
- Stainless Steel: with a fiber laser, 400 to 600 DPI (the fiber preset is 508). Diode and CO₂ need a marking spray.
- Cork: the grain hides fine detail, so going above your laser’s DPI gains nothing. Pick bold, high-contrast photos.
These are starting points. Burn a test card on a scrap piece to see what your machine and material like best: Make a DPI test card.
How ImagePrep360 handles DPI
- You choose the size and the laser. The app works out the exact pixel count (size × DPI, rounded) and resizes the photo to it before dithering, so every pixel is one spot.
- The DPI is written into the file: the PNG’s pHYs chunk and the BMP header carry it, so laser software reads the real size.
- The LightBurn .lbrn2 export sets the image size in mm and the line interval to 25.4 ÷ DPI, so the import keeps the size.
- In LightBurn, keep the image at that size and use Pass-Through for a dithered file, so it is not resampled or dithered a second time.
Not sure of your spot size? The DPI helper in the app turns a spot size or a laser type into a DPI, with a cheat sheet of common values.