Why the type of laser matters
Hobby and small-shop engravers use a handful of light sources, and the wavelength decides almost everything: which materials absorb the beam, which ones it passes straight through, and which safety glasses you need. This guide walks through the common types, the two ways a machine moves the beam, and what each laser can and cannot do on the materials people engrave most.
Treat it as a map, not a settings sheet. Models differ, so your machine's manual and a quick test on scrap always have the final word.
Blue diode lasers
Blue diode lasers are the most common entry machines. Their light is blue, typically around 445 to 455 nm. Dark and organic materials such as wood, leather, cork, card and slate absorb it well. Clear acrylic and clear glass let most of it pass through, so they need paint, tape or a coating before a blue diode will mark them.
Watch the power figure. A diode module has an electrical power (what it draws from the power supply) and an optical power (the light that comes out). Some listings lead with the electrical number, which is several times higher: one builder's log lists a module sold as 40 W that puts out about 15 W of light. Compare machines by optical power, and check the spec sheet when a number looks too good.
Higher-power modules usually combine several laser diodes into one beam, sold as spot compression or as dual or quad diode modules. That adds power for cutting and faster engraving, but the combined spot can be larger or less round than a single diode's, which can soften fine photo detail. The stated spot size, typically about 0.08 to 0.1 mm on common 5 to 20 W modules, matters as much as the watts.
CO₂ lasers: glass tubes and RF tubes
CO₂ lasers emit far infrared light at 10.6 µm. Wood, paper, leather, acrylic, glass, stone and most other non-metals absorb it strongly, which is why CO₂ machines cut clear acrylic easily and frost glass. Bare metal reflects it, so a CO₂ laser marks steel only with a marking compound or spray.
There are two kinds of CO₂ source. Glass DC tubes are cheaper and common in hobby machines; one maker quotes them at typically 2,000 to 4,000 hours, after which the tube is replaced. RF metal tubes cost more, are quoted at 10,000 hours or more, can be recharged, and respond faster when the laser switches on and off, which helps crisp detail at high engraving speeds. The tube type alone does not set the spot size: the lens, the beam path and the alignment matter too.
Most CO₂ machines are gantry machines with a large bed for cutting. Galvo CO₂ machines also exist: they steer the beam with mirrors and mark small areas on non-metals very quickly, but they are not built for cutting large sheets.
Fiber lasers: Q-switched and MOPA
Fiber lasers emit near infrared light at 1064 nm, which metals absorb far better than CO₂ light. They engrave and mark steel, stainless, aluminium, brass, titanium and precious metals without sprays, and they mark many plastics. Most clear materials let 1064 nm pass, and on wood a fiber laser gives little more than a surface scorch. Hobby fiber machines are almost always galvo machines with a small field.
Q-switched fiber sources fire pulses of a fixed length, typically around 100 to 200 nanoseconds. They are the cheaper choice and work well for engraving and marking metal. MOPA sources let you set the pulse length (one source maker lists 2 to 500 ns) and the frequency separately. That control is what makes colour marking on stainless steel practical: the laser grows a thin oxide layer whose thickness shows as gold, purple, blue and other colours. MOPA also gives better black or white marks on anodized aluminium and cleaner marks on many plastics. Colour results depend on the steel, the focus and careful tests.
Infrared 1064 nm add-on modules
Several diode machine makers sell small 1064 nm infrared modules that swap in for the blue head. They are pulsed sources with a low average power: one maker lists about 2 W average with very short peaks of around 15 kW. That is enough to mark bare metal without spray, and to mark opaque plastics, leather and stone.
They are not a fiber laser in a different box. On a gantry they are slow, the marks are shallow (that maker quotes about 0.05 mm at most), they cannot cut anything thicker than foil, and they do not mark clear acrylic. The beam is invisible, so you need glasses rated for 1064 nm, not your blue diode glasses. The source type and power vary by brand, so read your own module's spec sheet.
UV lasers and cold marking
UV lasers emit at 355 nm, made by tripling the frequency of a 1064 nm source. Most materials absorb this short wavelength strongly and close to the surface, and the light can break chemical bonds directly instead of melting or burning. That is why UV marking is called cold marking: the zone affected by heat is very small.
It suits glass, many plastics, silicone, ceramics and heat-sensitive parts where a CO₂ or fiber laser would melt, crack or discolour the surface. UV machines are usually galvo markers with a small field, and they typically cost more than diode or CO₂ machines. They mark; they are not for cutting thick material.
Gantry vs galvo: two ways to move the beam
A gantry machine moves the laser head on X and Y rails, like a plotter, and the beam points straight down. The work area is as big as the rails, so gantries suit cutting and large engravings. Speed is limited by moving the head: entry machines typically engrave at a few hundred mm/s.
A galvo machine keeps the head still and steers the beam with two small, fast mirrors, then through a flat-field lens. Because only the mirrors move, it can mark at thousands of mm/s, but the field is small, typically around 100 to 300 mm square depending on the lens. Galvos are mainly for marking and fine engraving, not for cutting sheets.
Enclosed vs open frame
Laser safety classes describe the laser light a person can reach, not the power of the source. An enclosed machine with interlocks and a filtered viewing window can be sold as a Class 1 product even though the laser inside is Class 4. That is how enclosed laser cutters are classed: safe to stand next to while the lid is shut and the interlocks work.
An open-frame machine has no enclosure, so you are exposed to the Class 4 laser itself. Direct beams and even diffuse reflections off the work can damage eyes, and the beam can start fires. Everyone in the room needs glasses rated for the wavelength, and you need your own fume extraction. Opening a Class 1 machine during a job, defeating an interlock or removing panels takes you back to the class of the laser inside. Laser safety covers the details.
Rotary attachments
A rotary attachment turns round items such as tumblers, glasses and pens under the beam, so the laser can engrave around them. A roller rotary sets the item on turning wheels: quick to load, and good for straight or slightly tapered items. A chuck rotary grips the item in jaws: better for odd shapes and items that would slip.
Your software needs to know how far to turn. In LightBurn you enter the steps (or mm) per rotation from the rotary's documentation and, for a chuck, the diameter of each item; the Test button should turn exactly one full turn and back. If an engraving comes out stretched or squashed around the item, one of those values is wrong. Galvo machines can use rotaries too.
Which laser for which material
A general guide for the materials people engrave most. Results vary with the machine, the power and the exact material, so run a test on scrap first.
- Engraveengraves well, with visible depth or a strong mark and no coating
- Cutcuts through thin to medium sheet, and engraves
- Marksurface mark only, or only with a coating, spray, paint or special settings
- Nodoes not work in practice: the beam passes through or bounces off
- Neverunsafe on every laser: toxic or corrosive smoke
| Material | Blue diode (~450 nm) | CO₂ (10.6 µm) | Fiber (1064 nm) | UV (355 nm) |
|---|---|---|---|---|
| Wood and plywood | EngraveEngraves well; cuts thin sheet in several passes. | CutEngraves and cuts. | MarkSurface scorch only. | MarkLight surface mark. |
| Cast acrylic | MarkClear passes the beam; only dark opaque sheet or a coating works. | CutEngraves frosty white; cuts cleanly. | NoClear passes 1064 nm. | MarkFine surface marks; test first. |
| Extruded acrylic | MarkAs cast: clear does not absorb blue. | CutCuts with glossy edges; engraves less frosty than cast. | NoClear passes 1064 nm. | MarkFine surface marks; test first. |
| Slate | EngravePale marks; good for photos. | EngravePale marks; good for photos. | MarkMarks; test the power. | MarkMarks. |
| Glass | MarkOnly with paint or a coating; bare glass passes the beam. | EngraveFrosts the surface; can chip, a wet paper layer helps. | NoMostly passes through. | MarkCold marking with little cracking. |
| Anodized aluminium | MarkRemoves the dye to show bare metal. | MarkRemoves the dye. | MarkRemoves the dye; MOPA can give black or white. | MarkMarks; test first. |
| Bare steel and stainless | MarkOnly with a marking spray; bare metal reflects. | MarkOnly with a marking compound. | EngraveEngraves and anneals; MOPA can colour stainless. | MarkLight surface marks. |
| Leather (veg-tan) | EngraveEngraves well; never chrome-tanned or PVC faux leather. | CutEngraves and cuts. | MarkPossible, rarely used. | MarkLight marks. |
| Cork | EngraveEngraves well. | CutEngraves and cuts thin sheet. | MarkSurface scorch only. | MarkLight marks. |
| Ceramic tile | MarkPainted tile or toner method. | MarkGlaze ablation or a marking compound. | MarkMarks some glazes; test first. | MarkMarks ceramics. |
| Paper and card | CutCuts and engraves card; watch for flare-ups. | CutCuts and engraves; watch for flare-ups. | NoScorches; little use. | MarkFine marks. |
| PVC and vinyl | NeverGives off hydrogen chloride. | NeverGives off hydrogen chloride. | NeverGives off hydrogen chloride. | NeverGives off hydrogen chloride. |
PVC and vinyl are never for any laser. Heated, they release hydrogen chloride (which forms hydrochloric acid with moisture) along with other toxic compounds. That harms your lungs and corrodes the machine. Many faux leathers are PVC, so they belong on the list too. Laser safety has the full list of materials never to burn.
Infrared 1064 nm add-on modules behave like a slow, shallow fiber laser: they mark metals, opaque plastics and leather, and not clear materials.
How ImagePrep360 helps
ImagePrep360 prepares the photo, not the laser settings, but it knows which kind of laser you use. Pick your laser type and the app starts from a DPI that suits its spot:
- Diode: 254 DPI
- CO₂: 254 DPI
- CO₂ fine: 318 DPI
- Fiber: 508 DPI
- Galvo / UV: 423 DPI
DPI explained shows how spot size and DPI fit together.
Pick the material and the preset sets invert, mirror, tone and dither for it, so slate, anodized aluminium and glass come out the right way round. Materials and invert explains each default.
When the file is ready, download a PNG with the DPI embedded, a BMP, or a LightBurn .lbrn2 project at the right physical size, with the image mode set so LightBurn does not dither it a second time.
Sources
The pages this guide was checked against. Specifications vary by model, so your machine's own documentation comes first.
- Epilog Laser: What are the wavelengths of the laser sources?
- Thunder Laser: RF laser vs DC glass laser, which one to choose?
- JPT: MOPA vs Q-switched fiber lasers
- KEYENCE: UV laser marking, precision for sensitive materials
- xTool Support: FAQ on the xTool 1064 nm infrared laser module
- Hackaday.io build log: diode module input power vs optical power
- LightBurn Documentation: Rotary mode (DSP), roller and chuck rotaries
- LightBurn Documentation: Rotary on galvo lasers
- OSHA Technical Manual, Section III, Chapter 6: Laser Hazards
- Carnegie Mellon University EHS: Laser Cutter Safety Guideline
- Trotec Laser: Which materials are not suitable for laser cutting and engraving?