Skip to content

Laser safetyBeginner8 min read

Laser safety: classes, eyewear, fumes and fire

What laser classes mean for hobby machines, how to read the OD and wavelength on safety glasses, fume extraction, fire habits, materials never to burn, and a printable pre-job checklist.

Start with your manual

Hobby lasers are safe to use when you respect three things: the beam, the smoke and the heat. This guide explains each in plain terms, so you can read your machine's safety section with confidence. It is general information, not a substitute for that manual or for the rules where you live and work. Where they say something more specific, follow them.

None of this needs expensive gear. Most of it is habit: the right glasses on, the extraction running, someone watching the job, and the wrong materials kept out of the machine.

Laser classes in plain words

Laser products are classed under IEC 60825-1 (and ANSI Z136 in the US) by how much laser light a person can reach in normal use, not by the power of the source alone.

Class 1
Safe in normal use. Many Class 1 products hold a far more powerful laser fully enclosed behind interlocks, like an enclosed laser cutter with its lid shut.
Class 2
Low-power visible beams, up to 1 mW for a continuous beam. The blink reflex normally protects you, but do not stare into the beam.
Class 3R
Up to five times the Class 2 limit, about 1 to 5 mW for a visible beam. Low risk, but looking into the beam can harm the eye.
Class 3B
Up to 500 mW for a continuous beam. The direct beam and mirror-like reflections injure eyes; diffuse reflections are normally safe.
Class 4
Above 500 mW. The direct beam and even diffuse reflections can injure eyes and skin, and the beam can start fires. The lasers inside engraving and cutting machines are almost always Class 4.

What that means at home: an open-frame engraver exposes you to a Class 4 laser, so glasses are not optional for anyone in the room. An enclosed machine sold as Class 1 is Class 1 only while its lid is shut, its interlocks work and its panels are on. Open it during a job, defeat a switch or run it with a panel off, and you are back to Class 4. Not every enclosed machine is sold as Class 1, so check the label on the machine and the class in its manual.

Eye protection: wavelength and optical density

Laser safety glasses work by absorbing one band of wavelengths. Their strength is given as optical density (OD), the base-10 logarithm of how much they cut the light: OD 4 lets through one ten-thousandth, OD 5 one hundred-thousandth, OD 6 one millionth. Each step up is ten times stronger.

A rating only counts at the wavelengths printed with it, and good eyewear is labelled with both the OD and the wavelengths it covers. European eyewear (EN 207) is marked with the laser mode (D for a continuous beam; I, R or M for pulses of different lengths), the wavelength or range in nm, and an LB number, for example D 532 LB6 or DI 750-1200 LB5. The LB number is a minimum OD that the filter must also keep while the beam is hitting it.

That is why glasses are not interchangeable. Lenses made for a blue 445 to 455 nm diode may pass 1064 nm fiber or infrared module light almost untouched unless 1064 nm is also printed on them, and glasses for 1064 nm or for CO₂ at 10.6 µm will not stop blue light unless their marking covers it. Check that the printed range includes your exact wavelength, with at least the OD your machine's manual asks for. For hobby diodes that is typically OD 4 or higher, and one infrared module maker asks for OD 5 or higher at 1064 nm. If you use two laser types, you need glasses for each, or glasses whose markings cover both.

Be wary of unmarked tinted glasses shipped with some low-cost machines: with no wavelength and OD printed on them, treat them as unrated. Treat tinted lids and windows the same way. On a machine certified as Class 1, the window is part of that rating. A coloured acrylic panel on an open machine, a home-made enclosure or an aftermarket lid is not protection unless its maker states the wavelength and OD. Even with rated glasses, never look straight at the beam or its bright spot, and never through a magnifier or binoculars.

Fumes and extraction

Laser engraving works by burning and vaporising material, and the smoke carries what the material was made of. Wood and MDF smoke contains fine soot and compounds such as formaldehyde, benzene and acrolein. Acrylic gives off its monomer (MMA) and formaldehyde. Leather, plastics, glues and coatings add their own. Smoke you can smell is smoke you are breathing.

The simplest safe set-up vents outdoors: an enclosed machine, or an enclosure around an open frame, with a fan pulling the smoke through a short, sealed duct to the outside, away from windows and air intakes. Let fresh air into the room to replace what the fan removes, and keep the fan running until the smoke has cleared.

Where you cannot vent outdoors, use a filter unit built for laser fumes, typically a pre-filter, a HEPA stage for fine particles and a deep bed of activated carbon for gases. Filters fill up, so change them on the maker's schedule. No filter makes the materials on the never list below safe.

Use metal or fire-rated duct where you can. Thin plastic hose can melt or burn, and resin from the smoke builds up inside any duct, so check it and clean it from time to time.

Fire: never walk away

Every engraving and cutting laser can set its work on fire, and cardboard, paper, thin wood and MDF flare up most easily. The rule is simple: never leave a running laser unattended. If you have to step away, pause or stop the job first.

Air assist, a jet of air at the focus, blows out small flames and keeps smoke off the lens, so use it whenever you cut. Keep a CO₂ fire extinguisher (or the type your manual names) within reach of the machine; a fire blanket is a useful extra for small fires outside it. If something catches and does not go out at once, stop the laser with the emergency stop or the power switch, then deal with the flame.

Clean regularly. Resin, soot and small offcuts collect on the bed, the honeycomb or slats, the tray and in the duct, and that build-up burns. Clear the bed and tray often, clean the lens and mirrors as the manual describes, and keep the area around the machine free of paper, solvents and other things that burn.

Materials never to burn

Some materials are unsafe on any laser, whatever its type or power. Their smoke is toxic, corrosive or both, and no filter fixes that. If you do not know what a material is, do not put it in the machine.

PVC, vinyl and most faux leather
Release hydrogen chloride and other toxic compounds. Harmful to breathe and corrosive to the machine.
PTFE (Teflon)
Releases fluorine compounds, including hydrogen fluoride, which is highly toxic.
Polycarbonate (Lexan, Makrolon)
Cuts badly: it chars, discolours and can catch fire, and its smoke contains benzene, toluene and other aromatic compounds.
Fiberglass and coated carbon fiber
The resin that binds them, usually epoxy, burns into harmful fumes, and the glass will not cut cleanly.
Coated, treated and flame-retardant materials
Treated wood, painted or coated sheet and flame-retardant plastics can contain chlorine, bromine or heavy metals. Ask the supplier for the safety data sheet first.
Chrome-tanned leather
Can contain chromium(VI) compounds. Use vegetable-tanned leather.
ABS, nylon and foams
Many university labs ban them: ABS, nylon and polyurethane release hydrogen cyanide, and ABS and polystyrene foam give off styrene and flare easily. Engrave an ABS-based sheet only if its maker says it is laser safe, and never without strong extraction.
Anything unknown
Unlabelled plastics, mystery offcuts and "leather" of unknown make. If you are unsure, don't.

For what each laser type can do with safe materials, see Types of lasers.

A pre-job checklist

Print this and keep it next to the machine. It is a reminder, not a replacement for your manual's own checklist.

Before you start

While it runs

When it finishes

Sources

The pages this guide was checked against. Your machine's manual and your local regulations come first.

  1. OSHA Technical Manual, Section III, Chapter 6: Laser Hazards
  2. Lasermet: Laser classes explained (IEC 60825-1)
  3. Lasermet: EN 207, CE marking and laser protective eyewear
  4. Carnegie Mellon University EHS: Laser Cutter Safety Guideline
  5. University of Florida EHS: Laser Cutter Materials
  6. Trotec Laser: Which materials are not suitable for laser cutting and engraving?
  7. xTool Support: FAQ on the xTool 1064 nm infrared laser module (eyewear rating)

Try it in the app

Set your material, size and laser, and ImagePrep360 makes a file at the exact pixel count, with the DPI written in.